Two modes for an efficient measurement strategy
“Seeker” mode is a broadband measurement for pre-testing and localising measurement points. It allows continuous, direct-reading measurement of the total concentration of all VOCs present. “Seeker” mode is similar to using a single-PID gas measurement device.

“Analysis” mode allows selective measurement for monitoring specific toxic compounds. Pre-defined target compounds can be precisely measured in seconds. “Analysis” mode is similar to gas chromatography analyses conducted in the laboratory.

Up to 90% time savings
The Dräger X-pid 9000/9500 requires no preparation and is ready to use after a brief start-up phase. Selective measurement in “Analysis” mode takes only a few seconds. A benzene measurement starts with the push of a button and is completed in only 30 seconds. After another 60 seconds, the device is ready to measure for benzene again. Compared with other detection systems, the Dräger X-pid 9000/9500 saves considerable time and enables further monitoring to be undertaken. Simultaneous measurement of other compounds, like benzene and butadiene, further reduces testing times.

Cost savings
Because no consumables are used to take measurements, operating costs can be reduced. For users with high measurement needs, the Dräger X-pid 9000/9500 quickly pays for itself. For example, it requires no pre-tubes, also making it easier to use and preventing user errors. On the basis of 200 measurements per year, the Dräger X-pid 9000/9500 is generally more cost-effective than comparable measurement systems.

High selectivity for greater safety
The selective measurement mode “Analysis” relies on technology which separates individual compounds present in mixed gases. This makes it possible to conduct a compound-specific measurement for benzene, even if other VOCs like toluene and xylene are also present in high concentrations. Cross-sensitivities for benzene are reduced to a minimum. This reduces the number of false-positive measurement results and false alarms.

Reliable performance under tough conditions
The influence on measurement results by environmental factors like variable ambient temperature or high humidity are reduced to a minimum. The sensor unit maintains a constant temperature above the ambient air temperature and separates water vapour from the target compounds. This ensures reliable measurements under tough environmental conditions.

Low detection limits
Concentrations of toxic compounds in the air at work sites must not exceed threshold limit values. Mandatory time-weighted averages in the low ppb to ppm range need to be performed for carcinogenic vapours like benzene. The Dräger X-pid 9000/9500 is optimised for measuring in this concentration range and detects benzene starting at 50 ppb.

Intuitive handling with mobile app
The sensor unit is controlled and the measurment data processing is conducted by a mobile app installed on an explosion-proof smartphone (delivery includes both). The large touch screen and familiar user interface elements are easy to use. This makes the sophisticated technology accessible to a broad group of users. No prior knowledge or extensive training is required.

Laboratory-quality measurement results
The gas measurement device is based on gas chromatography (GC) and photoionisation detection (PID) technologies. These technologies, used widely in laboratories, have a high acceptability due to their excellent analytical performance. The Dräger X-pid 9000/9500 brings these technologies directly to the hazardous area of any production site.

Simple functional test and calibration
The functional test with the test gas isobutylene and toluene is done in just two minutes and the Dräger X-pid 9000/9500 is ready to use. During the test the user is guided through the user interface step-by-step. The calibration is completed within about four minutes.

Two product models for different requirements
There are two models of the product: the 9000 and 9500. The Dräger X-pid 9000 covers the target compounds benzene and butadiene. The Dräger X-pid 9500 offers the possibility of combining more than 23 target compounds into individual analysis programmes and thus expanding its application range. This means, you can independently expand the target substance database for the Dräger X-pid 9500.

 

• To order contact us via:
  
  Phone: Call +44 (0)330 088 0560
• Email: [email protected]
• Web Form: Get a quote




Dräger X-pid 9000	6851847
Dräger X-pid 9500	68 51848
Upgrade X-pid®	on request
Calibration
Test gas 10 ppm isobutylene / 10 ppm toluene, 58 L	6814046
Test gas 5 ppm benzene, 58 L	6814050
Calibration Accessories
Test gas 10 ppm isobutylene / 10 ppm toluene, 58 L	6814046
Test gas 5 ppm benzene, 58 L	6814050
Control valve basic 0.5 LPM	6810397
Power supply Dräger X-pid	6851844
Bags and Cases
Case for Dräger X-pid® 9000 / 9500	6851851
Carrying strap Dräger X-pid	6851846
Hoses with 5 mm inner diameter
FKM hose (color black, solvent resistant), max. order length 50 meter	1203150
PTFE-lined Tygon hose, 3 meters	8326980
PTFE-lined Tygon hose, spool of 15 meters	4594679
Hoses with 3 mm inner diameter
FKM hose (color black, solvent resistant), max. order length 100 meter	8325837
FKM hose (color black, solvent resistant), 5 meter incl. adapters	8325705
FKM hose (color black, solvent resistant), 10 meter incl. adapters	8325706
FKM hose (color black, solvent resistant), 20 meter incl. adapters	8325707
Probes
Float probe (w/o hose)	6802337
Float probe with 5 cm hose and 5mm luer female adapter	8327654
Telescopic probe ES 150	8316533
Bar probe 90, with accessories	8316532
Bar probe 400	8317188
Float probe (incl. 3 m FKM hose with 3 mm inner diameter)	8325831
Adapters
Spare set filter X-am 125 pump/X-dock, consisting of 1x water and dust filter, 1x hose connector for pump, 1x Adaptor male	8319364
Gassing adapter Dräger X-pid, to be used for bumptests and calibrations	6851850

 

• Datasheet